Build log

Everything that's happened so far.

Newest first. Each post is a short write-up of what I did, what worked and what didn't. The bar below shows where the project is right now.

Concept & enclosureSep 2026
First boardsOct 18 2026
lilvo system 1.xOct 26 2026 →
Beta boardsfirst full prototype Nov 16
Production & open sourcethe goal
November 2026
Nov 16, 2026

The first fully working one

New board, white shell, and for the first time everything works: both screens, touch, L / R, the lid, sound. Hand-assembled, but I can finally play on it like a real console.

hardwaremilestone
Read the post →
Nov 3 – 16, 2026

lilvo 1.5 to 1.6: a battery you can trust

I measured a full discharge and found the "1000 mAh" battery held about 590. The battery readout is now calibrated, learns your battery by itself, and the system updates in one safe step.

software
Read the post →
Nov 9 – 16, 2026

Two new boards that wouldn't start

Both RevD.8 boards came back dead. A week of measuring, a forum thread and an X-ray later: the main chip's big centre pad wasn't soldered. The fix is in RevE.1.

hardware
Read the post →
Nov 4, 2026

How small it really is

Numbers don't really get it across, so here's the second prototype next to a phone, my other handhelds and a few keychain consoles.

hardware
Read the post →
Nov 2, 2026

The second prototype, assembled

The new main board is still on its way, but the new shell, hinge cable, speaker and lid board arrived. After some filing and sanding, it all went together and works. Everything except L / R.

hardwaremilestone
Read the post →
October 2026
Oct 28, 2026

Themes, and NEON on the real thing

The system now has four themes. Each one changes the layout and how consoles are drawn, not just the colours. NEON is the first one I filmed on the prototype.

softwaremilestone
Read the post →
Oct 26, 2026

lilvo system 1.0

Launcher, 12 consoles, save states with screenshots, close-the-lid saving and a web page for files. Everything since Oct 19 rolled into one install.

softwaremilestone
Read the post →
Oct 25, 2026

The enclosure, layer by layer

Five shell parts, a steel hinge pin and a spring detent, all inside 18 mm. An exploded view of how it goes together.

hardware
Read the post →
Oct 25, 2026

Inside the boards

Three boards, one chip, two independent screens. How the electronics fit under a 2-inch screen, and why the lid carries almost nothing.

hardware
Read the post →
Oct 24, 2026

Managing games from a browser

Plug in USB-C, open lilvo.local, drag games in. Covers, saves, BIOS files and system updates all live on one web page served by the console.

software
Read the post →
Oct 22, 2026

Ordered the Beta boards

A 6-layer main board that should be close to final, plus a new lid board and hinge cable. Two independent reviews went into it.

hardware
Read the post →
Oct 21, 2026

It's a handheld now

Board, both screens and the hinge cable in one printed shell, held together with tape. For the first time I can hold it, play and close it.

hardwaremilestone
Read the post →
Oct 20, 2026

The launcher on real screens

The home screen I had been mocking up now runs on both screens of the bare board. 3D consoles are drawn in software, no GPU.

software
Read the post →
Oct 18, 2026

First power-on

The first prototype boards came back. Voltages good, Linux boots, both screens show a test pattern at 60 fps. Same night: my first post on r/SBCGaming.

hardwaremilestone
Read the post →
Oct 2 – 12, 2026

Proving the chip on a dev board

Before trusting my own boards, I ran the whole software stack on a MangoPi dev board and wired a real screen to it. 75 MHz, 60 fps, no dropped frames.

hardwaresoftwaremilestone
Read the post →
September 2026
Sep 2026

Where it started

I knew very little about hardware. I picked a chip, two small screens and a shape, then spent a month on boards, hinges and printed shells.

milestone
Read the post →